Differences

This shows you the differences between two versions of the page.

--- projects:3dprint:troubleshooting [2023/10/20 08:27] – [Retraction speed] jattie
+++ projects:3dprint:troubleshooting [2023/10/20 18:04] (current) – [Print speed] jattie
@@ Line 21: / Line 21: @@
   * Wiping
   * Combing
+  * Z-hop
+^Parameter^Start^Increment^
+^Retraction distance|6mm|1mm|
+^Retraction distance sprite|0.6mm|0.1mm|
+^Retraction speed|25mm/s|5mm/s|
+^Retraction speed sprite|85mm/s|5mm/s|
+^Retraction minimum travel|5mm|5mm|
+^Travel speed|2 x print|5-10mm/s|
+^Nozzle temperature|220-255|5|
+^Print speed|60mm/s|5-10mm/s|
+^Coasting|nozzle dia cubed/0.064mm cubed|0.01mm cubed|
+^Wipe distance|1.2mm|0.01mm|
+^Combing|disabled|enabled|
+^Z-hop|enable/0.2mm|0.1mm|
 ===== Retraction speed =====
-To correct the retraction speed setting, you can start by increasing the retraction speed by increments of 5 millimeters/second. If adjusting the retraction speed made the situation better, you can use smaller increments for fine-tuning. For a sprite extruder start with 0.6mm and 85mm/s ((https://www.crealityexperts.com/creality-sprite-extruder-pro-upgrade-kit-install-guide#:~:text=In%20your%20slicer%20software%2C%20be,and%2085%20mm%2Fs%20speed.)
+To correct the retraction speed setting, you can start by increasing the retraction speed by increments of 5 millimeters/second. If adjusting the retraction speed made the situation better, you can use smaller increments for fine-tuning. For a sprite extruder start with 0.6mm and 85mm/s ((https://www.crealityexperts.com/creality-sprite-extruder-pro-upgrade-kit-install-guide#:~:text=In%20your%20slicer%20software%2C%20be,and%2085%20mm%2Fs%20speed.))
 ===== Retraction distance =====
@@ Line 38: / Line 56: @@
 ===== Travel speed =====
-To correct the travel speed setting, increase the travel speed value by increments of 5-10 millimeters/second until you find a balanced value where you don’t experience any blobs, stringing, or ghosting.
+To correct the travel speed((https://www.wevolver.com/article/tips-to-improve-petg-bed-adhesion)) setting, increase the travel speed value by increments of 5-10 millimeters/second until you find a balanced value where you don’t experience any blobs, stringing, or ghosting.
 Travel moves should be as fast as possible, at least 120 mm/s, to avoid oozing.
@@ Line 50: / Line 68: @@
 ===== Print speed =====
-PETG is very sensitive to print speed. Print too fast, and you’ll have poor layer adhesion, extruder skipping, and low print quality, but print too slow, and you’ll end up with deformed parts, stringing, and oozing.
+PETG is very sensitive to print speed.((https://www.wevolver.com/article/tips-to-improve-petg-bed-adhesion)) Print too fast, and you’ll have poor layer adhesion, extruder skipping, and low print quality, but print too slow, and you’ll end up with deformed parts, stringing, and oozing.
-In general, the material is best printed at a slow speed, ideally around 60 mm/s. This leads to improved bonding and cooling, and consequently better print quality. Some users report good results with faster speeds for the first layers.
+In general, the material is best printed at a slow speed, ideally around 60 mm/s. This leads to improved bonding and cooling, and consequently better print quality. //Some users report good results with faster speeds for the first layers.//
 To correct the print speed setting, increase the print speed value by increments of 5-10 millimeters/second until you push it to the highest value where you don’t experience any problems.